New for 2018!   Twin Scan 4

Twin Scan 3 can be upgraded, click here.

 

 

Twin Scan 4 CANBUS Scan Tool

· Compatible with 2011-2018 Softail®, 2012-2017 Dyna® and 2014+ Sportster® and 2014+ Touring models with CAN data bus (all models with a 6-pin diagnostics connector)*. 

· New software for 2018! Uses laptop PC for display. Includes software for Windows 7/8/10.

 · All of the same great features as Twin Scan 3:

· Reads and clears diagnostic trouble codes from engine control module (ECM), BCM (body control module), speedometer, and anti-skid braking system (ABS)

· Real time display of engine data on instrument panel type display

· Anti-skid brake system (ABS) brake bleeding functions.

· Built-in data logging. Stores up to one hour of data. Automatically triggers when a trouble code is set. Shows data before and after code is set

· Includes two analog inputs with 0-20V or ±200V range. Dual channel scopemeter capability for waveform display. The analog inputs can also be used for air/fuel ratio (AFR).

· Compact size: 3.2"L x 2.2"W x 1.0"H

 

· All new features of the Twin Scan 4:

· KEYFOBS and SECURITY: Program and read key fobs, program PIN and disable security.

· ACTIVATE MODULES, LIGHTS, and INDICATORS: Test different actuators, lights and indicators. Fuel pump drain and electronic throttle sweep.

· SPEEDOMETER*: Calibrate speedometer, remove new speedometer display of VinErr.

· ENGINE CONTROL SETTINGS*: Enable or disable settings in the ECM such as ACR (automatic compression release for performing engine compression testing), EITMS, cruise control, and active exhaust, read and set* engine idle speed rpm.

· BODY CONTROL SETTINGS*: Enable or disable settings in the BCM for ignition switch, new radio installation, bank angle sensor for trike installs, program fog light function, ABS installation, and enable service state.

· UPDATES FOR LIFE: Latest software will include latest firmware for easy remote updating of the Twin Scan 4.

 

 

Twin Scan Complete Kit

· Includes both Twin Scan II ABS (for 2001-2014 models with J1850 data bus), Twin Scan 4 (for 2011+ models with CAN data bus, 6-pos DLC connector), WEGO IIID for tuning capability with both Twin Scan versions, and the Twin Scan 3 Probe Kit for use with the scopemeter feature of the Twin Scan 4.  

· Ideal tuning aid for Screamin Eagle® Pro Super Tuner (SEST), Dynojet® Power Commander®, and Daytona Twin Tec Twin Tuner. Twin Scan software analyzes logged data and displays AFR and the required volumetric efficiency (VE) correction (in percent) with the same RPM rows and throttle position sensor (TPS) or manifold pressure (MAP) columns used in these systems' tables. 

· Twin Scan 4 software can directly copy and paste to an Excel spreadsheet that you can use to calculate the required corrections and then copy and paste the data to the Pro Super Tuner or Power Commander® software. You can also directly export calculated fuel correction data to Twin Tuner data files.  

 

Twin Scan Complete Kit

Visit the Twin Scan 4 Tech FAQ for more detailed information about engine tuning and diagnostics!

 

Order online using Paypal or call us at 386-322-7390  (Monday-Friday 9 AM to 5 PM Eastern time) for credit card and COD orders. For online orders, please email any special instructions to sales@daytona-twintec.com. 

 

All products covered by our 1 year limited warranty.

 

Part Number Description Suggested Retail
15500
Twin Scan 4 Low Cost Scan Tool (for 2011+ models with CAN data bus (6-pos DLC connector). Includes USB cable and software on CDROM)
No license, no recurring subscription fees, all future Twin Scan 4 updates are free.
$511.00

15302 Twin Scan Probe Kit (for use with Twin Scan 4 scopemeter feature. Includes two insulation piercing probes and 12 volt power adapters for general purpose use) $94.00

15600 Twin Scan Complete Kit (includes both Twin Scan II ABS and Twin Scan 4 units, WEGO IIID Interface, two Bosch LSU 4.2 wide-band oxygen sensors, two 18 x 1.5 mm weld nuts, two 18 x 1.5 mm hex socket plugs, USB cable, probe kit, and software on CDROM) $1391.00

15304 Twin Scan WEGO Upgrade Kit (for customers with any Twin Scan II, 3 or 4 version. Includes WEGO IIID Interface, two Bosch LSU 4.2 wide-band oxygen sensors, two 18 x 1.5 mm weld nuts, and two 18 x 1.5 mm hex socket plugs) $439.00


Twin Scan 3 ABS Upgrade to Twin Scan 4. The unit must be sent to Daytona TwinTec for updating. Contact us at 386-304-0700 for details. $140.00
 

New 2011-2018 Harley-Davidson® motorcycles use the CAN data bus for communications between the engine control module (ECM), instrument module (IM), body control module (BCM), anti-skid braking system (ABS) and diagnostic scan tools. The Twin Scan 4 connects to the six terminal Deutsch style data link connector on the H-D® wiring harness and requires a laptop PC for user interface and data display.

The Twin Scan 4 features stand-alone data logging (no laptop PC attached). This feature provides diagnostic capabilities not found in any other available tools. The Twin Scan 4 is especially useful for diagnosing hard to find intermittent trouble codes. The motorcycle can be operated while the unit is installed. Under normal conditions (no trouble code), the unit can be set up to store data for the last hour of operation. If a trouble code is set, the unit automatically stops logging data 30 minutes after the code is set. Even days or weeks later, you can download the data. You can examine in detail what happened before and after the code was set. You have a range of capabilities for analyzing and printing out logged data that is displayed in a chart recorder format.

Download Twin Scan 4 Instructions

 

Twin Scan 4 Software

The Twin Scan 4 software has an easy to use menu system. All of the tasks are easy to find and select. The main menu will take the user to any of these several major functions: reading and clearing diagnostic trouble codes, displaying real time engine data, displaying logged data in chart format, program keyfob and security settings, analyze AFR data when used with optional WEGO IIID, oscilloscope display of signal waveforms using scopemeter, configuration settings for BCM, ECM & Speedometer, activate modules to test various engine actuators, bcm controlled lights, and speedometer cluster warning lights.

Diagnostic Trouble Codes

The unit will display information for all available modules (this includes the speedometer and tach on models with the instrument module on the data bus and the ABS). The upper half of the screen displays the system ID and calibration code information. The lower half of the screen displays diagnostic trouble codes. Each current and historic trouble code is displayed along with a brief description. The software includes a database of all diagnostic trouble codes published by Harley-Davidson®. You can then refer to the H-D® Electrical Diagnostic Manual for your model for detailed explanations and troubleshooting flowcharts.

You can print the displayed information to any Windows printer by clicking on the Print Codes button. You can clear any codes by clicking on the Clear Codes button.

 

 

Diagnostic Trouble Code Display

ABS Brake Bleeding Functions

Individual front and rear ABS brake bleeding functions are available. If you are only servicing the front or rear brake section, you do not need to bleed the opposite section. ABS brake bleeding should only be performed by a trained and experienced mechanic.

  

ABS Tools Display

Real Time Engine Data

You can display real time engine data on an instrument panel type layout with round tach and speedometer gauges and bar graph type gauges for most other parameters. Barometric pressure, idle RPM and system status are displayed in additional boxes. If the engine is not running, most values will appear as zero.

You can log data directly to the laptop PC while real time engine data display is active by clicking on the Start Data Logging button. Data is logged to a buffer memory on the laptop PC that stores one hour of data at 10 samples/second (3600 samples). You can start and stop data logging as desired. The last 3600 samples will remain in the program data buffer.

 

Real Time Engine Data Display

Data Logging

You can display data downloaded from the Twin Scan 4 (if the unit has been operated on the motorcycle in stand-alone mode) or directly logged while real time display was active. The logged data appears on a chart recorder type screen. The screen snapshot below shows the complete set of parameters. You have a range of capabilities for analyzing and printing the data. Data can also be saved to a file for future reference.

 

Data Logging Chart Display

 

AFR Data Analysis

The Twin Scan 4 Plus kit includes the WEGO IIID dual channel wide-band oxygen sensor system. When the WEGO IIID is connected, the Twin Scan 4 will log engine data along with the actual front and rear cylinder air/fuel ratio (AFR). The Twin Scan 4 Plus is an ideal tuning aid for use with the new Screamin Eagle® Pro Super Tuner (SEST) or Dynojet® Power Commander® on fuel injected motorcycles. The figure below shows logged AFR data that has been analyzed and displayed in Twin Cam format. You can select from multiple formats so that AFR data is displayed with the same RPM rows and throttle position sensor (TPS) or manifold pressure (MAP) columns used with most engine mapping systems.  

AFR Data Display

 

You can also display and print out the required volumetric efficiency (VE) correction (in percent) based on the AFR command. This gives you the required fuel correction. You can add data from an unlimited number of files that you previously saved. The data will be analyzed and incorporated into the table. Cells that vary more than ±0.5 AFR from the command value are shaded blue for rich or red for lean.

 

VE Percent Correction Display

 

You can use two approaches to make the required corrections in third party engine mapping systems. If you have Microsoft Office with Excel, you can directly copy and paste data from the Twin Scan 4 software to an Excel spreadsheet and then copy and paste from the Excel spreadsheet into the engine mapping software. In the Twin Scan 4 software, you can select a range of cells with the mouse and right click to bring up a copy menu. You can also left click on the upper left legend cell to select the entire table and then right click to bring up the copy menu. For more details on using Excel, including sample spreadsheets, please visit the Twin Scan 3 Tec FAQ. Alternately, you can manually enter the required corrections in the engine mapping software by referring to the printed VE percent correction table and marking off cells as you edit them. When used with the Daytona Twin Tec Twin Tuner, the program can directly export VE correction data to Twin Tuner data files.

 

Scopemeter Feature

The unit includes a scopemeter feature that allows display of two signal waveforms and is very useful for diagnostic purposes, such as looking at coil and injector drive signals to determine why a cylinder isn't firing. Waveforms can be printed and saved to a file for future reference. In scopemeter mode, the Twin Scan 4 can be used on earlier models and other makes of motorcycles. We offer a probe kit with insulation piercing probes and power adapters for use on earlier models and other makes. Refer to the Probe Kit Instructions for details including reference waveforms and diagnostic tips. Visit the Twin Scan 4 Tech FAQ for additional information.


Scopemeter Display of coil vs. crank pickup sensor waveform

 

 
Probe Kit for use on any motorcycle or vehicle

 

Key Fobs and Security Settings

The Twin Scan 4 is capable of reprogramming the wireless key fobs and the security PIN.  Also, the key fobs can be disabled to eliminate the need for the fobs.

Program Key Fobs and PIN 

 

ECM Enable and Disable Settings

The ECM (engine control module) settings feature allows programming of the ACR (automatic compression release), EITMS (engine idle temp management system), cruise control enable/disable and active exhaust setting. Also is the ability to clear fuel trims.

 
Program ECM Settings 

 

ECM Idle Speed Setting

The Twin Scan 4 is capable of reprogramming the idle speed*. Simple interface allows fast reading and setting of the idle speed value.


 

Program Engine Idle Speed

BCM Enable and Disable Settings

The BCM (Body Control Module) settings can be read and changed with a few simple clicks. For example, the Ignition switch can be deleted and the BCM can be programmed to only use the run/stop switch. The fog light can be programmed to be independent from the high beam.  The BAS (bank angle sensor) can be disabled with installing a trike kit. Radio & ABS installation, and a one key-cycle disable of the security for servicing.

 
Program Body Control Module Settings

 

Speedometer Calibration and Pairing

The Twin Scan 4 can read and program the speedometer calibration* using two methods. The first method is to use a known speed from a radar, gps or dyno and also enter the indicated speed. The other method is to perform your own calculation and enter a calibration value manually. Also available is a speedometer pairing feature.  This is useful when a speedometer is replaced, it will indicate "VinErr" until this CAN function is performed.

 
Calibrate Speedometer and Pairing

 

 

The Twin Scan 4 software runs under Microsoft Windows XP/Vista/Win7/Win8/Win10. We no longer support older Windows versions. Minimum PC requirement is a 300 MHz Pentium with super VGA display (SVGA with 1024 x 768 pixel resolution). The Twin Scan 4 connects to the PC by means of a USB interface. A USB cable is supplied with the unit. The PC must have a free USB port. If you have an older PC without USB capability, you cannot use the Twin Scan 4. For more detailed product information, we suggest that you download the Twin Scan 4 software and instructions. The software download includes sample files with actual data.

Download Twin Scan Software 

 

 

* Note: Not all features are available for all models. Most features are available for almost all models through 2016. For example, the 2017 and newer models have eliminated the adjustability of idle rpm and speedometer calibration for everyone at this time.

 

All trademarks on this website whether registered or not, are the property of their respective owners. The authors of this website are not sponsored by or affiliated with any of the third-party trademark or third-party registered trademark owners, and make no representations about them, their owners, their products or services.

Rev Twin_Scan4.0.1