Downloads

Daytona Twin Tec 2016 Catalog
(click on catalog to download)

 

Scroll down to find your product section. Each product section has installation instructions, tech notes, USB driver, and software downloads. Firmware updates for the TCFI and VRFI series are at the very bottom of this page.

Installation instructions and tech notes are in the form of PDF files and require Adobe  Acrobat Reader. If you do not have Adobe Acrobat Reader installed, click on the Adobe graphic to download it for free.

TCFI and VRFI Fuel Injection Controllers

Installation Instructions and Tech Notes

TCFI III Installation & Tuning Manual (includes software instructions) 

TCFI EX Installation & Tuning Manual

 

New! TCFI Gen 4 Quick Start Guide (step-by-step pictorial)

TCFI Gen 4 Installation & Tuning Manual (includes software instructions)

 

New! TCFI Gen 5 Quick Start Guide (step-by-step pictorial)

TCFI Gen 5 Installation & Tuning Manual (includes software instructions)

 

New! TCFI Gen 6 Quick Start Guide (step-by-step pictorial)

TCFI Gen 6 Installation & Tuning Manual (includes software instructions)

 

TCFI Gen 7 Installation & Tuning Manual (includes software instructions)

 

VRFI Gen 3 Installation & Tuning Manual (includes software instructions)

VRFI Gen 4 Installation & Tuning Manual (includes software instructions)

 

Bluetooth Interface Instructions

 

TCFI Idle Tuning Tech Note

TCFI Low Idle RPM Tech Note

TCFI III ACR System Tech Note

TCFI Series 100 kPa Speed-Density Firmware Tech Note

TCFI Series 300 kPa Speed-Density Firmware Tech Note

VRFI Series 100 kPa Speed-Density Firmware Tech Note

VRFI Series 300 kPa Speed-Density Firmware Tech Note

 

Fuel Calculator for 100 kPa Speed-Density Systems

300 KPA Fuel Injector Calculator

3Bar Map Sensor Wiring Diagram

WEGO Wire Harness Drawings (Zip File)

 

USB Driver

To install the USB driver required for all products with USB interface, click on the link below. Before installing the USB driver, make sure that your USB device is not connected to your PC. The USB driver is compatible with Windows XP/Vista/7/8/10. It will not install on older PCs running Windows 98 or ME. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. When the File Download dialog box appears, click on "Run this program from its current location." Ignore any security warnings and click on Yes to continue. After installation of the driver is complete, connect the USB device. The Windows Found New Hardware Wizard will appear and complete installation of the USB device. Then refer to the COM Port Configuration section in the instructions for your device to properly configure its USB interface using Device Manager.

USB Driver

 

Windows Software

Click on the software that you want to download. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. These materials are in the form of compressed files that utilize the new Windows Installer service for an easy one click install. The software is compatible with Windows XP/Vista/7/8/10. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. When the File Download dialog box appears, click on the Run option. Instruction sheets to accompany our software are listed in the section above. For TCFI and VRFI series, check the table below to see what software version your product requires.

PC Link TCFI Software Version 18.1

PC Link TCFI EX Software Version 3.0

TCFI Log Software Version 18.1

PC Link software includes basic setup files. Additional setup files for special applications:

TCFI Setup File List

TCFI Setup Files

The setup files are saved as a ZIP archive file that you can download by clicking on the link above. You will require PKZIP to unzip the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website.

 

PC Link VRFI Software Version 14.2

VRFI Log Software Version 14.1

PC Link software includes basic setup files. Additional setup files for special applications:

VRFI Setup File List

VRFI Setup Files

The setup files are saved as a ZIP archive file that you can download by clicking on the link above. You will require PKZIP to unzip the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website.

 

Twin Tuner Fuel Injection Controllers

Installation Instructions and Tech Notes

Twin Tuner Instructions

Twin Tuner CAN Bus Instructions

Twin Tuner Touring Model CAN Bus Instructions

Twin Tuner EX Instructions

Twin Tuner Touring Model Instructions

Twin Tuner Sportster® Instructions

Twin Tuner for 2003-2007 Buell® Tech Note

Twin Tuner for 2008 Buell® Tech Note

 

Twin Tuner II Instructions

Twin Tuner II CAN Bus Instructions

Twin Tuner II Touring Model CAN Bus Instructions

Twin Tuner II Touring Instructions

Twin Tuner II V-Rod Instructions

USB Interface Instructions

 

USB Driver

To install the USB driver required for all products with USB interface, click on the link below. Before installing the USB driver, make sure that your USB device is not connected to your PC. The USB driver is compatible with Windows XP/Vista/7/8/10, 32-bit or 64-bit machines. It will not install on older PCs running Windows 98 or ME. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. When the File Download dialog box appears, click on "Run this program from its current location." Ignore any security warnings and click on Yes to continue. After installation of the driver is complete, connect the USB device. The Windows Found New Hardware Wizard will appear and complete installation of the USB device. Then refer to the COM Port Configuration section in the instructions for your device to properly configure its USB interface using Device Manager.

USB Driver

 

Windows Software

Click on the software that you want to download. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. These materials are in the form of compressed files that utilize the new Windows Installer service for an easy one click install. The software is compatible with Windows XP/Vista/7/8/10, 32-bit or 64-bit machines. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. When the File Download dialog box appears, click on the Run option. Instruction sheets to accompany our software are listed in the section above. For TCFI and VRFI series, check the table below to see what software version your product requires.

PC Link Tuner Software Version 5.0

Tuner Log Software Version 3.0

Twin Tuner Setup File List (includes Twin Tuner EX and Twin Tuner II) 

Twin Tuner Setup Files (includes Twin Tuner EX and Twin Tuner II)

The setup files are saved as a ZIP archive file that you can download by clicking on the link above. You will require PKZIP to unzip the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website.

 

Ignition Systems for Carbureted Motorcycles

Installation Instructions and Tech Notes

 

Model 1005 Installation Instructions 

Model 1005 Installation Instructions (German Language Version) 

Model 1005 EX Installation Instructions

Model 1005-IH Installation Instruction

Model 1005S EX Installation Instruction 

Model 1006/1007 EX Installation Instructions

PC Link Evo Instructions 

Operating Statistics Software Instructions

 

TC88 Installation Instructions 

TC88 EX Installation Instructions

TC88A Installation Instructions

TC88A EX Installation Instructions

TC88A-IH Installation Instructions

PC Link TC88 Instructions 

TC88A Log Instructions 

 

VT-i Installation Instructions

 

Mini Coil Instructions

Single Fire Coil Instructions

Twin-Cam Coil Instructions

Universal Wire Set Instructions

 

Ignition Power Relay Kit Installation Instructions

Power Adapter Instructions

USB Interface Instructions

VOES Switch Instructions

 

Buell® Blast Tech Note

Dual Spark Plug Tech Note

Model 1005 Two Stage Tech Note

TC88 Stage Limit Tech Note 

Turbo Boost and Nitrous Timing Retard Tech Note

 

USB Driver

To install the USB driver required for all products with USB interface, click on the link below. Before installing the USB driver, make sure that your USB device is not connected to your PC. The USB driver is compatible with Windows XP/Vista/7/8/10, 32-bit or 64-bit machines. It will not install on older PCs running Windows 98 or ME. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. When the File Download dialog box appears, click on "Run this program from its current location." Ignore any security warnings and click on Yes to continue. After installation of the driver is complete, connect the USB device. The Windows Found New Hardware Wizard will appear and complete installation of the USB device. Then refer to the COM Port Configuration section in the instructions for your device to properly configure its USB interface using Device Manager.

USB Driver

 

Windows Software

Click on the software that you want to download. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. These materials are in the form of compressed files that utilize the new Windows Installer service for an easy one click install. The software is compatible with Windows XP/Vista/7/8/10, 32-bit or 64-bit machines. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. When the File Download dialog box appears, click on the Run option. Instruction sheets to accompany our software are listed in the section above. For TCFI and VRFI series, check the table below to see what software version your product requires.

PC Link Evo Software Version 8.1 

Operating Statistics Software Version 7.0

 

PC Link TC88 Software Version 8.1 

TC88A Log Software Version 3.0 

 

Twin Scan and WEGO Diagnostic Tools and Tuning Aids

Installation Instructions and Tech Notes

Twin Scan II ABS Instructions (also applicable to original Twin Scan II)

Twin Scan 3 ABS Instructions (also applicable to original Twin Scan 3)

Twin Scan 3 Probe Kit Instructions

WEGO III Single Channel Installation Instructions

WEGO III Dual Channel Installation Instructions

 

WEGO IIID Installation Instructions (for use with Twin Scan II)

WEGO Single Channel Data Logging Software Instructions

WEGO Dual Channel Data Logging Software Instructions

WEGO Tach Adapter Installation Instructions

 

Hayabusa® Tech Note

Motorcycle Exhaust Sniffer Tech Note

WEGO Dynojet® Interface Tech Note

WEGO SuperFlow® Interface Kit Tech Note

 

USB Driver

To install the USB driver required for all products with USB interface, click on the link below. Before installing the USB driver, make sure that your USB device is not connected to your PC. The USB driver is compatible with Windows XP/Vista/7/8/10, 32-bit or 64-bit machines. It will not install on older PCs running Windows 98 or ME. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. When the File Download dialog box appears, click on "Run this program from its current location." Ignore any security warnings and click on Yes to continue. After installation of the driver is complete, connect the USB device. The Windows Found New Hardware Wizard will appear and complete installation of the USB device. Then refer to the COM Port Configuration section in the instructions for your device to properly configure its USB interface using Device Manager.

USB Driver

 

Windows Software

Click on the software that you want to download. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. These materials are in the form of compressed files that utilize the new Windows Installer service for an easy one click install. The software is compatible with Windows XP/Vista/7/8/10, 32-bit or 64-bit machines. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. When the File Download dialog box appears, click on the Run option. Instruction sheets to accompany our software are listed in the section above. For TCFI and VRFI series, check the table below to see what software version your product requires.

Twin Scan II Software Version 7.1 (for all Twin Scan II versions)

Twin Scan 3 Software Version 3.2 (for all Twin Scan 3 versions)

 

WEGO Single Channel Data Logging Software Version 9.2

WEGO Dual Channel Data Logging Software Version 4.1

 

TCFI and VRFI Firmware Updates

The following table lists the required software and possible upgrade paths for our TCFI and VRFI series. To determine the firmware revision of your module, use your current PC Link or Log software and download from the module. A message box will pop up with the module's firmware revision. To determine the version of  your software, click on About on the Help menu. If you attempt to load an incorrect firmware revision into your module or use any software versions other than the required software listed below, the module may become inoperative. Earlier versions of software are no longer supported, are not available for download, and will not run under Windows Vista/7/8. However you can upgrade your TCFI or VRFI module. Call our office at 386-304-0700 for details.

Product Firmware Revision Minimum Required Software Version Upgrade Path

TCFI Gen 1 

1.0 - 6.4

PC Link TCFI Ver. 8.22

TCFI Log Ver. 10.0

Contact us

TCFI II (single sensor)

1.0- 4.0

PC Link TCFI Ver. 8.22

TCFI Log Ver. 10.0

Contact us

TCFI IID (dual sensor)

5.0-5.24

PC Link TCFI IID Ver. 9.03

TCFI Log Ver. 10.0

Contact us

TCFI IID (dual sensor)

7.04-7.22

PC Link TCFI IID Ver. 10.0

TCFI Log Ver. 10.0

Contact us

TCFI III 

3.0

PC Link TCFI Ver. 17.0

TCFI Log Ver. 17.0

Upgrade module to Rev 3.33 

TCFI III 

3.33

PC Link TCFI Ver. 17.0

TCFI Log Ver. 17.0

Final revision 

TCFI EX 

3.33

PC Link TCFI EX Ver. 3.0

TCFI Log Ver. 15.1

Current revision 

TCFI Gen 4 

1.1-2.2

PC Link TCFI Ver. 17.0

TCFI Log Ver. 17.0

Optional upgrade to Rev 2.3

TCFI Gen 4 

2.3

PC Link TCFI Ver. 17.0

TCFI Log Ver. 17.0 

Current revision 

TCFI Gen 5 

1.07-2.2

PC Link TCFI Ver. 17.0

TCFI Log Ver. 17.0

Optional upgrade to Rev 2.3

TCFI Gen 5 

2.3

PC Link TCFI Ver. 17.0

TCFI Log Ver. 17.0

Current revision 

TCFI Gen 6 

2.08

PC Link TCFI Ver. 17.0

TCFI Log Ver. 18.0

Current revision

TCFI Gen 7 

1.70

PC Link TCFI Ver. 17.0

TCFI Log Ver. 18.0

Current revision 

TCFI Gen 7

TwinCooled® 

1.80

PC Link TCFI Ver. 18.1

TCFI Log Ver. 18.1

Current revision, all Gen7 production

       

VRFI (single sensor)

1.0-3.3

PC Link VRFI Ver. 3.31

VRFI Log Ver. 3.0

Contact us

VRFI (dual  sensor)

5.0-5.24

PC Link VRFID Ver. 4.02

VRFI Log Ver. 3.0

Contact us

VRFI Gen 3

3.4

PC Link VRFI Ver. 14.2

VRFI Log Ver. 14.1

Optional upgrade to Rev 4.3

VRFI Gen 3

4.3

PC Link VRFI Ver. 14.2

VRFI Log Ver. 14.1

Final revision

VRFI Gen 4

1.0-2.2

PC Link VRFI Ver. 14.2

VRFI Log Ver. 14.1

Recommended upgrade to Rev 2.3

VRFI Gen 4

2.3

PC Link VRFI Ver. 14.2

VRFI Log Ver. 14.1

Current revision

 

TCFI III (Gen 3) Firmware Update

You can update the firmware in TCFI III units. The firmware update package is a ZIP archive file that you can download by clicking on the link below. You will require PKZIP to unzip the individual files within the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website. Installation of the firmware update requires the Mega Boot Programmer software and accompanying instructions that you can also download by clicking on the links below. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. Read the instructions carefully before proceeding. Mega Boot Programmer software is compatible with Windows XP/Vista/7/8. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. Once you have installed Mega Boot Programmer software on your PC, you can continue to use it for any future TCFI III firmware revisions.

Warning: For use with TCFI III only.  If you try to use this firmware with a TCFI Gen I or Gen II unit, it will become inoperative and you must return it to the factory. 

TCFI III Rev 3.33 Firmware

TCFI III Rev 3.33 Firmware Update Tech Note

Mega Boot Programmer Software

Mega Boot Programmer Instructions

 

TCFI Gen 4 Firmware Update

The firmware update package is a ZIP archive file that you can download by clicking on the link below. You will require PKZIP to unzip the individual files within the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website. Installation of the firmware update requires the Mega Boot Programmer software and accompanying instructions that you can also download by clicking on the links below. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. Read the instructions carefully before proceeding. Mega Boot Programmer software is compatible with Windows XP/Vista/7/8. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. Once you have installed Mega Boot Programmer software on your PC, you can continue to use it for any future firmware revisions.

TCFI Gen 4 Rev 2.3 Firmware

TCFI Gen 4 Rev 2.3 Firmware Update Tech Note

Mega Boot Programmer Software

Mega Boot Programmer Instruction

 

TCFI Gen 5 Firmware Update

The firmware update package is a ZIP archive file that you can download by clicking on the link below. You will require PKZIP to unzip the individual files within the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website. Installation of the firmware update requires the Mega Boot Programmer software and accompanying instructions that you can also download by clicking on the links below. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. Read the instructions carefully before proceeding. Mega Boot Programmer software is compatible with Windows XP/Vista/7/8. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. Once you have installed Mega Boot Programmer software on your PC, you can continue to use it for any future firmware revisions.

TCFI Gen 5 Rev 2.3 Firmware

TCFI Gen 5 Rev 2.3 Firmware Update Tech Note

Mega Boot Programmer Software

Mega Boot Programmer Instruction

 

TCFI Gen 6 Firmware Update

The firmware update package is a ZIP archive file that you can download by clicking on the link below. You will require PKZIP to unzip the individual files within the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website. Installation of the firmware update requires the Mega Boot Programmer software and accompanying instructions that you can also download by clicking on the links below. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. Read the instructions carefully before proceeding. Mega Boot Programmer software is compatible with Windows XP/Vista/7/8. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. Once you have installed Mega Boot Programmer software on your PC, you can continue to use it for any future firmware revisions.

TCFI Gen 6 Rev 2.08 Firmware

TCFI Gen 6 Rev 2.08 Firmware Update Tech Note

Mega Boot Programmer Software

Mega Boot Programmer Instruction

 

TCFI Gen 7 Firmware Update

The firmware update package is a ZIP archive file that you can download by clicking on the link below. You will require PKZIP to unzip the individual files within the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website. Installation of the firmware update requires the Mega Boot Programmer software and accompanying instructions that you can also download by clicking on the links below. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. Read the instructions carefully before proceeding. Mega Boot Programmer software is compatible with Windows XP/Vista/7/8/10, 32-bit or 64-bit machines. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. Once you have installed Mega Boot Programmer software on your PC, you can continue to use it for any future firmware revisions.

TCFI Gen 7 Rev 1.80 Firmware             NOTE: Must use PC_Link and TCFI_Log minimum version 18.1 with this firmware

TCFI Gen 7 Rev 1.80 Firmware Update Tech Note

Mega Boot Programmer Software

Mega Boot Programmer Instruction

 

VRFI Gen 3 Firmware Update

The firmware update package is a ZIP archive file that you can download by clicking on the link below. You will require PKZIP to unzip the individual files within the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website. Installation of the firmware update requires the Mega Boot Programmer software and accompanying instructions that you can also download by clicking on the links below. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. Read the instructions carefully before proceeding. Mega Boot Programmer software is compatible with Windows XP/Vista/7/8. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. Once you have installed Mega Boot Programmer software on your PC, you can continue to use it for any future firmware revisions.

VRFI Gen 3 Rev 4.3 Firmware

VRFI Gen III Rev 4.3 Firmware Update Tech Note

Mega Boot Programmer Software

Mega Boot Programmer Instruction

 

VRFI Gen 4 Firmware Update

The firmware update package is a ZIP archive file that you can download by clicking on the link below. You will require PKZIP to unzip the individual files within the archive. If you do not have PKZIP installed on your computer, you can download it from the PKWARE Inc. website. Installation of the firmware update requires the Mega Boot Programmer software and accompanying instructions that you can also download by clicking on the links below. You must use Internet Explorer as your web browser. Firefox will not work and other web browsers are not supported. Read the instructions carefully before proceeding. Mega Boot Programmer software is compatible with Windows XP/Vista/7/8. We no longer support older Windows versions. For Windows Vista, you must disable the User Account Control (UAC) during installation as described in the Vista UAC Tech Note. Once you have installed Mega Boot Programmer software on your PC, you can continue to use it for any future firmware revisions.

VRFI Gen 4 Rev 2.3 Firmware

VRFI Gen 4 Rev 2.3 Firmware Update Tech Note

Mega Boot Programmer Software

Mega Boot Programmer Instruction